All

Step1：Install the support——iron pipe on the ground.Step2：Insert the al-alloy post vertically and install Aluminum Strip Seal.Step3：Install Aluminum Bottom Edge Cover.Step4：Install the fence board in turn.Step5：Install Aluminum Top Edge Cover.Step6：Fixed the posts and Aluminum Top Edge Cover with fasteners and screws.Step7：Fix the top cap.Learn about installing HOHEcotech WPC fence by checking out our Installation Guide video.https://youtu.be/02u5O7ehaQQ?si=7cUOh0Ocsry1hCnx

Step1：Draw a line horizontally on the wall at a distance of 40cm, and mark it every 40cm in the horizontal direction.Mark at 2.5cm above the intersection of the two lines, where the pre-drilling position is located.Step2：Drilling holes at the marks and fix in the white expansion tube.Step3：After cutting the joists, place it in align with the wall horizontal line.Mark the joist where the place is parallel to the pre-drilling holes, pre-drill at the mark, and then drive the expansion screws.Step4：Fix the bottom edge trim.Step5：Fix the first wall panel to the joist and install the remaining wall panels in turn.When the left site is not enough to put a whole decking, it can be cut according to the desired size to finish installation. Step6：Install side and top edge trims.Learn about installing HOHEcotech WPC wall cladding by checking out our Installation Guide video.https://youtu.be/02u5O7ehaQQ?si=7cUOh0Ocsry1hCnx

Step 1:Install the joist on the cement floor, and the gap between two adjacent joists is no more than 35cm.When the decking is to an end, please use two joists and gap between them is at least 5mm.Step 2:Install the first decking.Side-to-side gap between boards, End-to-end gap between boards, End-to-object gap is at least 5mm.Step 3: After pre-drilling on the joists, install the fasteners.Fix one fastener into the side slot, and then push another decking to the fasteners.Or slide the SY plastic fastener into the side slot and fix them with screws,Repeat this step to the end.When the left site is not enough to put a whole decking, it can be cuted according to the desired size to finish installation. Remember to reserve the 5mm gap.Step 4:Align the edge cover along side the decking edge and screw vertically.Learn about installing HOHEcotech WPC decking by checking out our Installation Guide video.https://youtu.be/02u5O7ehaQQ?si=7cUOh0Ocsry1hCnx

There is a 20 year limited residential warranty and 10 year limited commercial warranty. The most comprehensive warranty in the industry.

Co-extrusion decking has grooved boards that accept a hidden fastener system. The TC clip system has a 5mm gap and the MG system has a 1mm gap.

Co-extrusion heat retention is better than that of wood decking. Co-extrusion is used and performs as intended worldwide in countries with extreme heat conditions including Africa and Dubai.

Co-extrusion has mould inhibitors that prevent it growing on the inside of the board. Surface mould can still happen but this can be easily wiped clean and it will never penetrate Co-extrusion premium shield.

You can cut, nail, drill, screw and rout Co-extrusion with standard woodworking tools. The density of Co-extrusion is greater than wood so we recommend using a carbide tipped blade.

In the short term composite decking will cost more than a wooden deck. However, a wooden deck will require maintenance such as oiling or painting every year to keep it looking good. Co-extrusion is nearly maintenance free and has a longer life span than regular decking.

Years of engineering was spent to ensure the correct blend of components went into Co-extrusion. We are confident in the product and its long lasting performance so we have backed it with the most comprehensive warranty in the industry.

Hundreds of hours of direct UV testing has left minimal change to the colour of Co-extrusion composite boards.

Co-extrusion has been means tested above global regulatory standards. Lab testing rarely mimics real life, so we went above and beyond to make sure that you have peace of mind and that you can rely on our composite decking boards.

Co-extrusion’s premium shield encapsulates the board in an impermeable layer of protection. This makes Co-extrusion stain and fade resistant. The boards are waterproof so only sweeping and cleaning off debris and dirt is required for upkeep; ultra low maintenance and easily wiped clean.

Our products are made from 95% recycled materials, including clear plastic bottles and reclaimed wood fibers. We’re reduced our carbon footprint through waste reduction, energy conservation and a vertically integrated manufacturing process. Every month we save over 12,000,000 pounds of plastic from being buried in landfills.